Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Preporuka za kupovinu bušilice
#10
Wurth nije proizvodjac on je samo brend.
Makita se pravi u istoj fabrici gde se pravi i Vilager.
Sve sto sam pisao o Boschu mislio sam na palvu seriju jer u firmi druge i nemamo. A kasnije cu da vam opisem i jedno iskustvo sa ravnim rusilicama od Boscha.
Reply


Messages In This Thread
Preporuka za kupovinu bušilice - by Želja - 07-04-2017, 08:39 PM
RE: Preporuka za kupovinu bušilice - by Makso - 07-04-2017, 09:24 PM
RE: Preporuka za kupovinu bušilice - by Braca - 07-04-2017, 11:16 PM
RE: Preporuka za kupovinu bušilice - by Makso - 07-04-2017, 11:28 PM
RE: Preporuka za kupovinu bušilice - by BeliNinja - 07-05-2017, 06:06 AM
RE: Preporuka za kupovinu bušilice - by Bocko - 07-05-2017, 06:17 AM
RE: Preporuka za kupovinu bušilice - by vladd - 07-05-2017, 07:11 AM
RE: Preporuka za kupovinu bušilice - by Želja - 07-05-2017, 08:14 AM
RE: Preporuka za kupovinu bušilice - by ManicP - 07-05-2017, 09:41 AM
RE: Preporuka za kupovinu bušilice - by Braca - 07-05-2017, 11:06 AM
RE: Preporuka za kupovinu bušilice - by Bocko - 07-05-2017, 12:38 PM
RE: Preporuka za kupovinu bušilice - by Bocko - 07-05-2017, 04:44 PM
RE: Preporuka za kupovinu bušilice - by ManicP - 07-05-2017, 06:33 PM
RE: Preporuka za kupovinu bušilice - by Želja - 07-05-2017, 06:42 PM
RE: Preporuka za kupovinu bušilice - by mikikg - 07-05-2017, 10:25 PM
RE: Preporuka za kupovinu bušilice - by emiSAr - 07-06-2017, 08:40 AM
RE: Preporuka za kupovinu bušilice - by Želja - 07-06-2017, 01:29 PM
RE: Preporuka za kupovinu bušilice - by mikikg - 07-06-2017, 02:46 PM
RE: Preporuka za kupovinu bušilice - by Želja - 07-06-2017, 03:02 PM
RE: Preporuka za kupovinu bušilice - by Dragan83 - 07-06-2017, 08:57 PM
RE: Preporuka za kupovinu bušilice - by Dragan83 - 07-06-2017, 09:07 PM
RE: Preporuka za kupovinu bušilice - by vladd - 07-07-2017, 11:34 PM
RE: Preporuka za kupovinu bušilice - by Želja - 07-08-2017, 07:44 AM
RE: Preporuka za kupovinu bušilice - by emiSAr - 07-08-2017, 09:43 AM

Forum Jump:


Users browsing this thread: 13 Guest(s)