CNC motalica za transformatore

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

CNC motalica za transformatore

gorankg Offline

Offline

Posting Freak

Posts: 1.137
Threads: 27
Joined: Oct 2014
Reputation: 301

#250

04-07-2017, 06:56 PM (This post was last modified: 04-07-2017, 06:59 PM by gorankg.)

(04-07-2017, 04:29 PM)Milan94 Wrote: Potenciometrom je malo nezgodno podesavati jer lako prebacimo u drugom smeru iako to nezelimo da nam se desi zato tastere predlazem ukolio je to izvodljivo.

Ovo sa potenciometrom sam predložio samo za test drajvera. Ako želiš da testiraš samo DC motor mogu ti poslati hex. Ne menja smer tako lako. Struja kroz motor jeste nula na 50% duty ali postoji mrtva zona oko 50% gde promena duty ne znači da će i motor krenuti. Tako je kod mene.
Ja sam imao drugačiju šemu oko 6n137. Mora da je neka starija. Sa ovom je OK.

Reply

« Next Oldest | Next Newest »

Messages In This Thread

CNC motalica za transformatore - by Milan94 - 06-11-2015, 09:14 PM

RE: CNC motalica za transformatore - by TDA - 06-11-2015, 09:34 PM

RE: CNC motalica za transformatore - by BeliNinja - 06-11-2015, 09:38 PM

RE: CNC motalica za transformatore - by Milan94 - 06-11-2015, 09:53 PM

RE: CNC motalica za transformatore - by gorankg - 06-12-2015, 06:40 AM

RE: CNC motalica za transformatore - by Milan94 - 06-12-2015, 09:21 PM

RE: CNC motalica za transformatore - by gorankg - 06-13-2015, 08:03 PM

RE: CNC motalica za transformatore - by Milan94 - 06-13-2015, 08:53 PM

RE: CNC motalica za transformatore - by Milan94 - 06-18-2015, 04:24 PM

RE: CNC motalica za transformatore - by Makso - 06-18-2015, 04:42 PM

RE: CNC motalica za transformatore - by Bocko - 06-18-2015, 04:42 PM

RE: CNC motalica za transformatore - by Milan94 - 06-18-2015, 04:59 PM

RE: CNC motalica za transformatore - by emiSAr - 06-18-2015, 05:04 PM

RE: CNC motalica za transformatore - by Milan94 - 06-18-2015, 05:20 PM

RE: CNC motalica za transformatore - by Bocko - 06-18-2015, 06:17 PM

RE: CNC motalica za transformatore - by milepa. - 06-18-2015, 06:17 PM

RE: CNC motalica za transformatore - by Milan94 - 06-18-2015, 07:46 PM

RE: CNC motalica za transformatore - by milepa. - 06-18-2015, 08:11 PM

RE: CNC motalica za transformatore - by Milan94 - 06-18-2015, 08:29 PM

RE: CNC motalica za transformatore - by uki122 - 06-20-2015, 05:17 PM

RE: CNC motalica za transformatore - by Milan94 - 06-20-2015, 07:29 PM

RE: CNC motalica za transformatore - by uki122 - 06-20-2015, 08:49 PM

RE: CNC motalica za transformatore - by Milan94 - 06-20-2015, 08:53 PM

RE: CNC motalica za transformatore - by uki122 - 06-20-2015, 09:34 PM

RE: CNC motalica za transformatore - by Milan94 - 04-09-2016, 06:20 PM

RE: CNC motalica za transformatore - by Milan94 - 05-11-2016, 11:19 AM

RE: CNC motalica za transformatore - by mikikg - 05-11-2016, 11:51 AM

RE: CNC motalica za transformatore - by dlalkovic - 05-14-2016, 09:09 AM

RE: CNC motalica za transformatore - by Milan94 - 05-11-2016, 12:00 PM

RE: CNC motalica za transformatore - by mikikg - 05-11-2016, 12:10 PM

RE: CNC motalica za transformatore - by Milan94 - 05-11-2016, 12:13 PM

RE: CNC motalica za transformatore - by mikikg - 05-11-2016, 12:20 PM

RE: CNC motalica za transformatore - by Milan94 - 05-11-2016, 12:26 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-12-2016, 04:34 PM

RE: CNC motalica za transformatore - by Želja - 05-12-2016, 05:22 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-12-2016, 04:50 PM

RE: CNC motalica za transformatore - by mikikg - 05-12-2016, 05:13 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-12-2016, 05:16 PM

RE: CNC motalica za transformatore - by Milan94 - 05-13-2016, 08:09 AM

RE: CNC motalica za transformatore - by Želja - 05-13-2016, 08:39 AM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-13-2016, 03:49 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-13-2016, 11:04 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-16-2016, 06:52 AM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 07:48 AM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 12:03 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 12:09 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 12:18 PM

RE: CNC motalica za transformatore - by gorankg - 05-16-2016, 01:23 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 12:26 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 12:36 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 01:36 PM

RE: CNC motalica za transformatore - by gorankg - 05-16-2016, 01:43 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 01:52 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 01:43 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 01:45 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 02:00 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 02:02 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 02:14 PM

RE: CNC motalica za transformatore - by gorankg - 05-16-2016, 02:17 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 02:43 PM

RE: CNC motalica za transformatore - by gorankg - 05-16-2016, 02:15 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 02:47 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 02:50 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 03:17 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 03:54 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 04:19 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 04:28 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 04:35 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 04:40 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 04:49 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 05:00 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 04:56 PM

RE: CNC motalica za transformatore - by emiSAr - 05-16-2016, 05:00 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 05:02 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 05:10 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 05:32 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-16-2016, 06:10 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 06:20 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 06:25 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-16-2016, 06:46 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 07:57 PM

RE: CNC motalica za transformatore - by gorankg - 05-16-2016, 09:32 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 08:19 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 08:28 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 10:03 PM

RE: CNC motalica za transformatore - by gorankg - 05-16-2016, 10:21 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 10:24 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 10:29 PM

RE: CNC motalica za transformatore - by Želja - 05-16-2016, 10:31 PM

RE: CNC motalica za transformatore - by gorankg - 05-16-2016, 10:39 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 10:43 PM

RE: CNC motalica za transformatore - by Milan94 - 05-16-2016, 10:45 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 10:59 PM

RE: CNC motalica za transformatore - by mikikg - 05-16-2016, 11:35 PM

RE: CNC motalica za transformatore - by Želja - 05-17-2016, 07:02 AM

RE: CNC motalica za transformatore - by gorankg - 05-17-2016, 07:45 AM

RE: CNC motalica za transformatore - by Želja - 05-17-2016, 09:05 AM

RE: CNC motalica za transformatore - by Milan94 - 05-17-2016, 08:47 PM

RE: CNC motalica za transformatore - by gorankg - 05-17-2016, 09:11 PM

RE: CNC motalica za transformatore - by Milan94 - 05-24-2016, 04:57 PM

RE: CNC motalica za transformatore - by Želja - 05-24-2016, 06:48 PM

RE: CNC motalica za transformatore - by mikikg - 05-24-2016, 09:30 PM

RE: CNC motalica za transformatore - by mikikg - 05-24-2016, 10:05 PM

RE: CNC motalica za transformatore - by Milan94 - 05-24-2016, 10:11 PM

RE: CNC motalica za transformatore - by mikikg - 05-24-2016, 10:19 PM

RE: CNC motalica za transformatore - by mikikg - 05-24-2016, 10:27 PM

RE: CNC motalica za transformatore - by Milan94 - 05-24-2016, 10:38 PM

RE: CNC motalica za transformatore - by mikikg - 05-24-2016, 10:49 PM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 08:35 AM

RE: CNC motalica za transformatore - by mikikg - 05-25-2016, 10:29 AM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 10:57 AM

RE: CNC motalica za transformatore - by mikikg - 05-25-2016, 11:33 AM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 11:52 AM

RE: CNC motalica za transformatore - by Milan94 - 05-25-2016, 01:07 PM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 03:15 PM

RE: CNC motalica za transformatore - by Milan94 - 05-25-2016, 07:36 PM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 07:43 PM

RE: CNC motalica za transformatore - by Milan94 - 05-25-2016, 07:49 PM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 07:58 PM

RE: CNC motalica za transformatore - by Milan94 - 05-25-2016, 08:08 PM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 08:21 PM

RE: CNC motalica za transformatore - by vojinilic - 05-25-2016, 08:39 PM

RE: CNC motalica za transformatore - by Milan94 - 05-25-2016, 08:46 PM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 08:51 PM

RE: CNC motalica za transformatore - by vojinilic - 05-25-2016, 08:51 PM

RE: CNC motalica za transformatore - by vojinilic - 05-25-2016, 09:00 PM

RE: CNC motalica za transformatore - by Milan94 - 05-25-2016, 09:11 PM

RE: CNC motalica za transformatore - by vojinilic - 05-25-2016, 09:16 PM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 09:19 PM

RE: CNC motalica za transformatore - by Milan94 - 05-25-2016, 09:20 PM

RE: CNC motalica za transformatore - by vojinilic - 05-25-2016, 09:21 PM

RE: CNC motalica za transformatore - by vojinilic - 05-25-2016, 09:23 PM

RE: CNC motalica za transformatore - by Želja - 05-25-2016, 09:25 PM

RE: CNC motalica za transformatore - by vojinilic - 05-25-2016, 09:29 PM

RE: CNC motalica za transformatore - by Milan94 - 05-27-2016, 09:36 AM

RE: CNC motalica za transformatore - by gorankg - 05-27-2016, 10:10 AM

RE: CNC motalica za transformatore - by Želja - 05-27-2016, 11:43 AM

RE: CNC motalica za transformatore - by vojinilic - 05-27-2016, 12:15 PM

RE: CNC motalica za transformatore - by Milan94 - 05-27-2016, 07:28 PM

RE: CNC motalica za transformatore - by Želja - 05-27-2016, 07:48 PM

RE: CNC motalica za transformatore - by vojinilic - 05-27-2016, 07:41 PM

RE: CNC motalica za transformatore - by mikikg - 05-27-2016, 09:48 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-28-2016, 01:02 AM

RE: CNC motalica za transformatore - by mikikg - 05-28-2016, 11:04 AM

RE: CNC motalica za transformatore - by Khadgar2007 - 05-28-2016, 11:12 AM

RE: CNC motalica za transformatore - by Milan94 - 05-28-2016, 05:24 PM

RE: CNC motalica za transformatore - by Želja - 05-29-2016, 08:53 AM

RE: CNC motalica za transformatore - by gorankg - 05-28-2016, 10:53 PM

RE: CNC motalica za transformatore - by mikikg - 05-29-2016, 10:42 AM

RE: CNC motalica za transformatore - by mikikg - 05-29-2016, 11:01 AM

RE: CNC motalica za transformatore - by Milan94 - 05-29-2016, 02:19 PM

RE: CNC motalica za transformatore - by Želja - 05-29-2016, 03:27 PM

RE: CNC motalica za transformatore - by gorankg - 05-29-2016, 03:52 PM

RE: CNC motalica za transformatore - by Milan94 - 05-29-2016, 04:06 PM

RE: CNC motalica za transformatore - by mikikg - 05-29-2016, 05:44 PM

RE: CNC motalica za transformatore - by Želja - 05-29-2016, 07:13 PM

RE: CNC motalica za transformatore - by mikikg - 05-29-2016, 07:31 PM

RE: CNC motalica za transformatore - by Želja - 05-29-2016, 07:40 PM

RE: CNC motalica za transformatore - by mikikg - 05-29-2016, 07:41 PM

RE: CNC motalica za transformatore - by mikikg - 05-29-2016, 07:58 PM

RE: CNC motalica za transformatore - by Želja - 05-29-2016, 08:35 PM

RE: CNC motalica za transformatore - by mikikg - 05-30-2016, 05:30 PM

RE: CNC motalica za transformatore - by Milan94 - 06-09-2016, 10:36 AM

RE: CNC motalica za transformatore - by mikikg - 06-09-2016, 11:01 AM

RE: CNC motalica za transformatore - by Milan94 - 06-09-2016, 11:06 AM

RE: CNC motalica za transformatore - by mikikg - 06-09-2016, 11:15 AM

RE: CNC motalica za transformatore - by Milan94 - 06-09-2016, 11:22 AM

RE: CNC motalica za transformatore - by vojinilic - 06-09-2016, 01:35 PM

RE: CNC motalica za transformatore - by mikikg - 06-09-2016, 01:45 PM

RE: CNC motalica za transformatore - by vojinilic - 06-09-2016, 02:26 PM

RE: CNC motalica za transformatore - by gorankg - 06-09-2016, 11:40 PM

RE: CNC motalica za transformatore - by vojinilic - 06-10-2016, 06:14 AM

RE: CNC motalica za transformatore - by gorankg - 06-10-2016, 07:21 AM

RE: CNC motalica za transformatore - by vojinilic - 06-10-2016, 08:15 AM

RE: CNC motalica za transformatore - by gorankg - 06-10-2016, 09:23 AM

RE: CNC motalica za transformatore - by Milan94 - 06-09-2016, 10:21 PM

RE: CNC motalica za transformatore - by mikikg - 06-09-2016, 10:37 PM

RE: CNC motalica za transformatore - by vojinilic - 06-09-2016, 10:39 PM

RE: CNC motalica za transformatore - by vojinilic - 06-09-2016, 10:42 PM

RE: CNC motalica za transformatore - by mikikg - 06-09-2016, 10:47 PM

RE: CNC motalica za transformatore - by vojinilic - 06-09-2016, 10:53 PM

RE: CNC motalica za transformatore - by mikikg - 06-09-2016, 11:09 PM

RE: CNC motalica za transformatore - by vojinilic - 06-09-2016, 11:21 PM

RE: CNC motalica za transformatore - by Milan94 - 06-09-2016, 11:23 PM

RE: CNC motalica za transformatore - by vojinilic - 06-09-2016, 11:26 PM

RE: CNC motalica za transformatore - by Milan94 - 06-09-2016, 11:56 PM

RE: CNC motalica za transformatore - by gorankg - 06-10-2016, 07:05 AM

RE: CNC motalica za transformatore - by Milan94 - 06-10-2016, 08:10 AM

RE: CNC motalica za transformatore - by Želja - 06-10-2016, 08:18 AM

RE: CNC motalica za transformatore - by vojinilic - 06-10-2016, 08:32 AM

RE: CNC motalica za transformatore - by Želja - 06-10-2016, 08:41 AM

RE: CNC motalica za transformatore - by vojinilic - 06-10-2016, 08:44 AM

RE: CNC motalica za transformatore - by Želja - 06-10-2016, 08:50 AM

RE: CNC motalica za transformatore - by vojinilic - 06-10-2016, 09:39 AM

RE: CNC motalica za transformatore - by mikikg - 06-10-2016, 11:44 AM

RE: CNC motalica za transformatore - by npejcic - 06-10-2016, 12:30 PM

RE: CNC motalica za transformatore - by vojinilic - 06-10-2016, 01:59 PM

RE: CNC motalica za transformatore - by npejcic - 06-10-2016, 08:23 PM

RE: CNC motalica za transformatore - by Milan94 - 06-10-2016, 08:23 PM

RE: CNC motalica za transformatore - by vojinilic - 06-10-2016, 08:51 PM

RE: CNC motalica za transformatore - by Milan94 - 06-10-2016, 09:07 PM

RE: CNC motalica za transformatore - by gorankg - 06-10-2016, 10:02 PM

RE: CNC motalica za transformatore - by vojinilic - 06-10-2016, 09:24 PM

RE: CNC motalica za transformatore - by Želja - 06-10-2016, 10:17 PM

RE: CNC motalica za transformatore - by Milan94 - 06-10-2016, 10:25 PM

RE: CNC motalica za transformatore - by Milan94 - 06-28-2016, 09:01 AM

RE: CNC motalica za transformatore - by Khadgar2007 - 06-28-2016, 09:08 AM

RE: CNC motalica za transformatore - by Milan94 - 06-28-2016, 09:16 AM

RE: CNC motalica za transformatore - by Khadgar2007 - 06-30-2016, 11:40 AM

RE: CNC motalica za transformatore - by Želja - 06-30-2016, 12:22 PM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 08:10 AM

RE: CNC motalica za transformatore - by Želja - 07-01-2016, 08:56 AM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 09:08 AM

RE: CNC motalica za transformatore - by Želja - 07-01-2016, 09:27 AM

RE: CNC motalica za transformatore - by Khadgar2007 - 07-01-2016, 09:39 AM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 09:43 AM

RE: CNC motalica za transformatore - by Khadgar2007 - 07-01-2016, 10:31 AM

RE: CNC motalica za transformatore - by Želja - 07-01-2016, 11:05 AM

RE: CNC motalica za transformatore - by Khadgar2007 - 07-01-2016, 11:17 AM

RE: CNC motalica za transformatore - by Želja - 07-01-2016, 11:41 AM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 12:03 PM

RE: CNC motalica za transformatore - by Želja - 07-01-2016, 12:16 PM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 12:29 PM

RE: CNC motalica za transformatore - by Želja - 07-01-2016, 12:38 PM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 12:35 PM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 12:37 PM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 12:44 PM

RE: CNC motalica za transformatore - by vojinilic - 07-01-2016, 12:47 PM

RE: CNC motalica za transformatore - by Macola - 07-01-2016, 02:35 PM

RE: CNC motalica za transformatore - by Milan94 - 07-01-2016, 09:29 PM

RE: CNC motalica za transformatore - by Macola - 07-01-2016, 09:53 PM

RE: CNC motalica za transformatore - by Milan94 - 12-23-2016, 03:02 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 12-23-2016, 03:22 PM

RE: CNC motalica za transformatore - by Milan94 - 12-23-2016, 03:53 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 12-23-2016, 03:55 PM

RE: CNC motalica za transformatore - by Milan94 - 12-23-2016, 04:27 PM

RE: CNC motalica za transformatore - by Milan94 - 03-31-2017, 08:41 PM

RE: CNC motalica za transformatore - by Khadgar2007 - 03-31-2017, 10:00 PM

RE: CNC motalica za transformatore - by Milan94 - 03-31-2017, 10:07 PM

RE: CNC motalica za transformatore - by gorankg - 04-04-2017, 08:01 AM

RE: CNC motalica za transformatore - by Milan94 - 04-04-2017, 10:37 AM

RE: CNC motalica za transformatore - by Želja - 04-04-2017, 12:21 PM

RE: CNC motalica za transformatore - by mikikg - 04-04-2017, 11:03 PM

RE: CNC motalica za transformatore - by gorankg - 04-06-2017, 10:37 AM

RE: CNC motalica za transformatore - by mikikg - 04-06-2017, 11:06 AM

RE: CNC motalica za transformatore - by gorankg - 04-06-2017, 12:16 PM

RE: CNC motalica za transformatore - by Milan94 - 04-07-2017, 04:29 PM

RE: CNC motalica za transformatore - by gorankg - 04-07-2017, 06:56 PM

RE: CNC motalica za transformatore - by Milan94 - 04-07-2017, 07:13 PM

RE: CNC motalica za transformatore - by Želja - 04-07-2017, 05:27 PM

RE: CNC motalica za transformatore - by Milan94 - 04-07-2017, 05:57 PM

RE: CNC motalica za transformatore - by Milan94 - 04-23-2017, 06:02 PM

RE: CNC motalica za transformatore - by vojinilic - 04-23-2017, 06:17 PM

RE: CNC motalica za transformatore - by Želja - 04-23-2017, 06:32 PM

RE: CNC motalica za transformatore - by gorankg - 04-23-2017, 06:48 PM

RE: CNC motalica za transformatore - by Milan94 - 04-23-2017, 08:12 PM

RE: CNC motalica za transformatore - by Želja - 04-23-2017, 09:23 PM

RE: CNC motalica za transformatore - by Milan94 - 04-23-2017, 09:33 PM

RE: CNC motalica za transformatore - by Želja - 04-23-2017, 09:36 PM

RE: CNC motalica za transformatore - by Želja - 04-23-2017, 09:39 PM

RE: CNC motalica za transformatore - by Milan94 - 04-23-2017, 10:11 PM

RE: CNC motalica za transformatore - by Želja - 04-23-2017, 10:32 PM

RE: CNC motalica za transformatore - by Milan94 - 04-23-2017, 10:52 PM

RE: CNC motalica za transformatore - by mikikg - 04-24-2017, 02:03 AM

RE: CNC motalica za transformatore - by mikikg - 05-01-2017, 01:23 AM

RE: CNC motalica za transformatore - by gorankg - 04-24-2017, 06:43 AM

RE: CNC motalica za transformatore - by mikikg - 04-24-2017, 07:02 AM

RE: CNC motalica za transformatore - by Bocko - 04-24-2017, 02:53 PM

RE: CNC motalica za transformatore - by Milan94 - 05-01-2017, 08:40 AM

RE: CNC motalica za transformatore - by mikikg - 05-01-2017, 09:26 AM

RE: CNC motalica za transformatore - by Milan94 - 05-01-2017, 09:36 AM

RE: CNC motalica za transformatore - by Milan94 - 01-28-2020, 04:36 AM

RE: CNC motalica za transformatore - by gimba - 01-28-2020, 08:00 AM

RE: CNC motalica za transformatore - by pakonja - 01-28-2020, 09:54 AM

View a Printable Version

Forum Jump:

Users browsing this thread: 4 Guest(s)