|
DIY CNC PCB Router
|
04-04-2020, 12:27 AM
Bravo Gimba, zeljno ocekujem nove slikice i nove info. Ja sam isto bio vredan u spakovao moj cnc ruter koji sam zapoceo pre godinu ipo dana , i da ne bi ove situacije cenim da ga jos ne bih zavrsio. Saljem narednih dana slike u posebnoj temi, malo ozbiljnija naprava u pitanju, sa stepperima sa encoderom, 80% konstrukcije alu profili , izuzetno robusno , radna povrsina 450x450mm , no vise info kada skupim vremena da izbacim koju slikicu sa objasnjenjem.
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
DIY CNC PCB Router - by gimba - 04-03-2020, 12:41 PM
RE: DIY CNC PCB Router - by Želja - 04-03-2020, 07:04 PM
RE: DIY CNC PCB Router - by mikikg - 04-03-2020, 07:05 PM
RE: DIY CNC PCB Router - by ZASto - 04-03-2020, 09:48 PM
RE: DIY CNC PCB Router - by ddanijel - 04-04-2020, 12:27 AM
RE: DIY CNC PCB Router - by gimba - 04-04-2020, 07:49 PM
RE: DIY CNC PCB Router - by Želja - 04-04-2020, 08:53 PM
RE: DIY CNC PCB Router - by gimba - 04-04-2020, 09:37 PM
RE: DIY CNC PCB Router - by ZASto - 04-04-2020, 07:52 PM
RE: DIY CNC PCB Router - by gimba - 04-04-2020, 08:07 PM
RE: DIY CNC PCB Router - by ddanijel - 04-04-2020, 10:29 PM
RE: DIY CNC PCB Router - by gimba - 04-05-2020, 08:43 AM
RE: DIY CNC PCB Router - by ZASto - 04-04-2020, 11:08 PM
RE: DIY CNC PCB Router - by gimba - 04-05-2020, 09:08 AM
RE: DIY CNC PCB Router - by ddanijel - 04-05-2020, 11:17 AM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 09:22 AM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 07:55 AM
RE: DIY CNC PCB Router - by ddanijel - 04-06-2020, 11:48 AM
RE: DIY CNC PCB Router - by ZASto - 04-06-2020, 12:34 PM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 03:43 PM
RE: DIY CNC PCB Router - by ZASto - 04-06-2020, 04:23 PM
RE: DIY CNC PCB Router - by ddanijel - 04-06-2020, 05:41 PM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 08:22 PM
RE: DIY CNC PCB Router - by ZASto - 04-06-2020, 09:52 PM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 10:51 PM
RE: DIY CNC PCB Router - by gimba - 04-07-2020, 07:44 PM
RE: DIY CNC PCB Router - by ddanijel - 04-08-2020, 02:04 PM
RE: DIY CNC PCB Router - by gimba - 04-08-2020, 06:07 PM
RE: Sve i svašta - by branko tod - 04-03-2020, 02:05 PM
RE: Sve i svašta - by gimba - 04-03-2020, 02:22 PM
RE: Sve i svašta - by pakonja - 04-03-2020, 03:08 PM
RE: Sve i svašta - by gimba - 04-03-2020, 03:21 PM
RE: Sve i svašta - by pakonja - 04-03-2020, 03:25 PM
RE: Sve i svašta - by gimba - 04-03-2020, 04:21 PM
RE: Sve i svašta - by branko tod - 04-03-2020, 06:28 PM
RE: Sve i svašta - by mikikg - 04-03-2020, 06:38 PM
RE: Sve i svašta - by gimba - 04-03-2020, 06:50 PM
DIY CNC PCB Router - by mikikg - 04-03-2020, 06:56 PM
|
