Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
DIY CNC PCB Router
#7
(04-03-2020, 03:25 PM)pakonja Wrote: Ekstra... Ja sam razmisljao da pravim CNC motalicu za trafoe/kaleme.... I da isprintam nosace motora i vodjica ali me plasilo koliko ce to kompaktno da bude, sada si me ohrabrio! Smile

Ko nije probao nije ni uspeo!  Smile
Reply


Messages In This Thread
DIY CNC PCB Router - by gimba - 04-03-2020, 12:41 PM
RE: DIY CNC PCB Router - by Želja - 04-03-2020, 07:04 PM
RE: DIY CNC PCB Router - by mikikg - 04-03-2020, 07:05 PM
RE: DIY CNC PCB Router - by ZASto - 04-03-2020, 09:48 PM
RE: DIY CNC PCB Router - by ddanijel - 04-04-2020, 12:27 AM
RE: DIY CNC PCB Router - by gimba - 04-04-2020, 07:49 PM
RE: DIY CNC PCB Router - by Želja - 04-04-2020, 08:53 PM
RE: DIY CNC PCB Router - by gimba - 04-04-2020, 09:37 PM
RE: DIY CNC PCB Router - by ZASto - 04-04-2020, 07:52 PM
RE: DIY CNC PCB Router - by gimba - 04-04-2020, 08:07 PM
RE: DIY CNC PCB Router - by ddanijel - 04-04-2020, 10:29 PM
RE: DIY CNC PCB Router - by gimba - 04-05-2020, 08:43 AM
RE: DIY CNC PCB Router - by ZASto - 04-04-2020, 11:08 PM
RE: DIY CNC PCB Router - by gimba - 04-05-2020, 09:08 AM
RE: DIY CNC PCB Router - by ddanijel - 04-05-2020, 11:17 AM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 09:22 AM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 07:55 AM
RE: DIY CNC PCB Router - by ddanijel - 04-06-2020, 11:48 AM
RE: DIY CNC PCB Router - by ZASto - 04-06-2020, 12:34 PM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 03:43 PM
RE: DIY CNC PCB Router - by ZASto - 04-06-2020, 04:23 PM
RE: DIY CNC PCB Router - by ddanijel - 04-06-2020, 05:41 PM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 08:22 PM
RE: DIY CNC PCB Router - by ZASto - 04-06-2020, 09:52 PM
RE: DIY CNC PCB Router - by gimba - 04-06-2020, 10:51 PM
RE: DIY CNC PCB Router - by gimba - 04-07-2020, 07:44 PM
RE: DIY CNC PCB Router - by ddanijel - 04-08-2020, 02:04 PM
RE: DIY CNC PCB Router - by gimba - 04-08-2020, 06:07 PM
RE: Sve i svašta - by branko tod - 04-03-2020, 02:05 PM
RE: Sve i svašta - by gimba - 04-03-2020, 02:22 PM
RE: Sve i svašta - by pakonja - 04-03-2020, 03:08 PM
RE: Sve i svašta - by gimba - 04-03-2020, 03:21 PM
RE: Sve i svašta - by pakonja - 04-03-2020, 03:25 PM
RE: Sve i svašta - by gimba - 04-03-2020, 04:21 PM
RE: Sve i svašta - by branko tod - 04-03-2020, 06:28 PM
RE: Sve i svašta - by mikikg - 04-03-2020, 06:38 PM
RE: Sve i svašta - by gimba - 04-03-2020, 06:50 PM
DIY CNC PCB Router - by mikikg - 04-03-2020, 06:56 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)