DIY Electronic projects › Sve ostalo - Everything else › Sve i svašta v
Sve i svašta

Thread Rating:
  • 6 Vote(s) - 4.33 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Sve i svašta
samuki Offline
Posting Freak
*****
Posts: 2.093
Threads: 46
Joined: Mar 2013
Reputation: 160
#3.781
11-12-2016, 10:50 PM
Ko je za jednu partiju saha ? ????
Reply
samuki Offline
Posting Freak
*****
Posts: 2.093
Threads: 46
Joined: Mar 2013
Reputation: 160
#3.782
11-13-2016, 06:03 PM
Miki vidi ovo, Dvb t prijemnik za mobitelle! Moze li se prepraviti za Cb? ????

http://www.gearbest.com/networking-commu...75300.html
Reply
mikikg Offline
Administrator
*******
Posts: 8.475
Threads: 132
Joined: Apr 2013
Reputation: 3.518
#3.783
11-14-2016, 04:04 AM (This post was last modified: 11-14-2016, 04:27 AM by mikikg.)
(11-13-2016, 06:03 PM)samuki Wrote: Miki vidi ovo, Dvb t prijemnik za mobitelle! Moze li se prepraviti za Cb? ????

http://www.gearbest.com/networking-commu...75300.html

Hmm, nije nemoguce, mozda je to neko vec radio, potrazi malo.
Za taj DVB-T2 sigurno koriste one iste IC koje imaju i u RTL-SDR a za to ima SW.
Pokusaj iskopati informaciju koji chipset IC ima unutra.
Reply
Khadgar2007 Online
Posting Freak
*****
Posts: 2.684
Threads: 52
Joined: Sep 2014
Reputation: 981
#3.784
11-20-2016, 06:27 PM
Malo Tektronixa i kako se to nekada radilo. http://www.jacmusic.com/Tube-testers/TEK...-index.htm Big Grin
Reply
mikikg Offline
Administrator
*******
Posts: 8.475
Threads: 132
Joined: Apr 2013
Reputation: 3.518
#3.785
11-27-2016, 03:02 PM (This post was last modified: 11-27-2016, 03:09 PM by mikikg.)
https://www.youtube.com/watch?v=ASnvGwB51N0

https://www.youtube.com/watch?v=JqqiQtf0sRU

https://www.youtube.com/watch?v=Rwsf5UuWRuI

Joj, crko sam, "umesto trazis zenu ti pokemone juris" … Big Grin
Reply
tesla017 Offline
Moderator
*****
Posts: 1.645
Threads: 22
Joined: Mar 2013
Reputation: 748
#3.786
Video  11-27-2016, 07:15 PM
Website
Reply
Dackotronic Offline
Rain Man
*****
Posts: 1.128
Threads: 12
Joined: Sep 2015
Reputation: 847
#3.787
11-27-2016, 07:42 PM
Reply
TDA Offline
Somewhere in Time
*******
Posts: 8.262
Threads: 77
Joined: Apr 2013
Reputation: 1.643
#3.788
11-27-2016, 08:18 PM
Big GrinBig GrinBig Grin
Face up...make your stand and realise you're living in the golden years!
Reply
tesla017 Offline
Moderator
*****
Posts: 1.645
Threads: 22
Joined: Mar 2013
Reputation: 748
#3.789
11-27-2016, 08:41 PM
Website
Reply
Želja Offline
Posting Freak
*****
Posts: 1.966
Threads: 29
Joined: Jan 2015
Reputation: 669
#3.790
11-28-2016, 07:30 PM
Ha, Haaa..   24  24

Ova prigušnica se vrlo lako može prepraviti na vodeno hladjenje ...


Pozz
Reply
saggit Offline
Senior Member
****
Posts: 383
Threads: 8
Joined: Mar 2013
Reputation: 221
#3.791
12-02-2016, 07:27 PM
U Mikro Princu je rasprodaja elektrolita 3300µF/35V, po ceno od 9,99 din. komad.
Ima i ležečih i vertikalnih.
Mali izgubljeni vanzemaljac, 3.000.000.000.000.000 svetlosnih godina udaljen od svog doma
Reply
TDA Offline
Somewhere in Time
*******
Posts: 8.262
Threads: 77
Joined: Apr 2013
Reputation: 1.643
#3.792
12-02-2016, 08:01 PM
Fala na dojavi! Smile
Face up...make your stand and realise you're living in the golden years!
Reply
tesla017 Offline
Moderator
*****
Posts: 1.645
Threads: 22
Joined: Mar 2013
Reputation: 748
#3.793
12-04-2016, 02:51 PM
Ima li neko mozda sPlan za crtanje sema i simbola?
Website
Reply
LordZi Offline
Member
***
Posts: 182
Threads: 9
Joined: Oct 2015
Reputation: 258
#3.794
12-04-2016, 03:53 PM
(12-04-2016, 02:51 PM)tesla017 Wrote: Ima li neko mozda sPlan za crtanje sema i simbola?

Poslao sam ti na mail... Wink
I'm gonna live forever or die trying...
Reply
branko tod Away
Posting Freak
*****
Posts: 3.202
Threads: 72
Joined: May 2015
Reputation: 1.599
#3.795
12-05-2016, 07:36 PM
CNC router VCT4030R , sa komandnim modulom  RichAuto-A1X i softverom UcanCam 10.5 neće da radi dobro.
Krug izgleda ovako. Kontaktirali smo proizvođača par puta, bem li ga šta će na kraju da rekne. Ima li neko pojma
o ovom problemu? U protivnom ništa od prednjih ploča.


.pdf   IMG_2961.pdf (Size: 1,3 MB / Downloads: 34)
Reply
ZASto Offline
Uzgajivač šargarepe
****
Posts: 686
Threads: 8
Joined: Mar 2013
Reputation: 234
#3.796
12-05-2016, 09:47 PM
Luftovi, luftovi, ili ...
Make no mistake between my personality and my attitude.
My personality is who I am.
My attitude depends on who you are.

塞爾維亞文
Reply
branko tod Away
Posting Freak
*****
Posts: 3.202
Threads: 72
Joined: May 2015
Reputation: 1.599
#3.797
12-05-2016, 10:12 PM
Ili...
Reply
mikikg Offline
Administrator
*******
Posts: 8.475
Threads: 132
Joined: Apr 2013
Reputation: 3.518
#3.798
12-05-2016, 10:14 PM
Ili problem sa drajverom, "prokliza", mozda je prebrzo podesen, mora da se proba vise puta na razlicitim koordinatama i sa razlicitim Feed rate.
Reply
Želja Offline
Posting Freak
*****
Posts: 1.966
Threads: 29
Joined: Jan 2015
Reputation: 669
#3.799
12-05-2016, 10:15 PM (This post was last modified: 12-05-2016, 10:17 PM by Želja.)
Nisu to luftovi, mada i oni umeju praviti probleme.

To pre liči na problem sa motion controlerom na toj mašini.
Koliko se sećam kada je Branko kupio tu mašinu, bilo je reči o USB konekciji prema PC.

Upravo u tim USB kontrolerima može ležati dosta problema, jer se upravo u njima
vrši konverzija G koda u Step/dir impulse prema drajverima.

Velika većina tih USB kontrolera je "nedoradjena" jer to što moraju da izvrše nije ni malo lak zadatak.

***

Mach3 je recimo prešao dug i trnovit razvojni put da bi na kraju bio "sasvim upotrebljiv" softver bez nekih
posebnih grešeka u radu. Mnogo je bilo medjuverzija i revizija dok se nisu popravili svi bagovi ...

Mach3 je u izvornoj varijanti predvidjen za LPT port, i to tako radi bez problema.

Već kada se na Mach3 prikači neki USB motion kontroler, koji tada preuzima svu interpolaciju na sebe
Mach3 ostane samo kao "go" ekran koji šalje putem USB konekcije linije G-koda , a ti kontroleri dalje na sebe
preuzimaju "sav posao".

I eto problema, ako nije USB kontroler uradjen kako treba. Imao sam priliku da vidim neke USB kontrolere
za Mach3 koji nemaju akceleraciju i deceleracijuz prilikom kretanja motora i niz sličnih propusta ...

***
Naša domaća firma iz centralne Srbije je skoro izbacila na tržište jedan takav USB kontroler za Mach3.
Nadam se da su sve uradili kako treba, inače će imati dosta reklamacija ...


===
Branko, ne mogu sa sigurnošću tvrditi štra je kod tebe uzrok, ali vrlo je moguće
da imaš gore opisani problem.


Postavi tvoj g-kod od tog kruga da ga pogledam.


P.S.
Kako izlaze recimo kocke, jesu li one pravilne ?

Pozz
Reply
mikikg Offline
Administrator
*******
Posts: 8.475
Threads: 132
Joined: Apr 2013
Reputation: 3.518
#3.800
12-05-2016, 10:37 PM (This post was last modified: 12-05-2016, 10:38 PM by mikikg.)
Krug na CNC je isto sto i XY prikaz na OSC, vidi se "linearnost" i krug je zanimljiv slucaj sto ima dve ose fazno pomerene koje idu od min do max i natrag i tu se menja feedrate od npr 1000 do 0 pa zatim promene smer pa opet ubrzanje.
Kroz takav raspon "frekvencija" ima jedna mala "crna rupa" ili rezonatna ucestanost motora i to da ne verujete uvek je tu gde najvise problema moze da napravi, u toj tacki motor prokliza i ne moze da se predvidi gde ce i koliko da ode, ode "random" 23 koraka i tome slicno … Dakle probaj prvo smanjiti feed rate. Da li kontroler moze brze ili sporije to moras da ustanovis, ako "baguje" stalno pri bilo kom feed rate onda postavi G-CODE da proverimo sta je stvarno zadato da se nacrta?
Reply


Forum Jump:


Users browsing this thread: 85 Guest(s)