DIY Electronic projects › Merenja i merni uređaji - Measurements and Equipment › Merenja i merni uređaji - Measurements and Equipment v
Spržio sam tester :(

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Spržio sam tester :(
mikikg Offline
Administrator
*******
Posts: 8.708
Threads: 138
Joined: Apr 2013
Reputation: 3.606
#21
05-26-2017, 01:18 PM
Hmm, pomocicu, nego nemam trenutno laptop, crko ...
Kuci imam sve sto treba, jedino da skoknemo do mene ili da poneses neki svoj laptop ...
Reply
TDA Offline
Somewhere in Time
*******
Posts: 8.261
Threads: 77
Joined: Apr 2013
Reputation: 1.643
#22
05-26-2017, 02:27 PM (This post was last modified: 05-26-2017, 02:28 PM by TDA.)
Poneću ja laptop. Nije problem.
Ponesi i ti svoj laptop pa ga možda i oživim na licu mesta.
Ozbiljan sam.
Poneću ZD939L. Smile

P.S.
Koji laptop je u pitanju?
Face up...make your stand and realise you're living in the golden years!
Reply
mikikg Offline
Administrator
*******
Posts: 8.708
Threads: 138
Joined: Apr 2013
Reputation: 3.606
#23
05-26-2017, 02:35 PM
Ma nema nista od mog laptop, Mac Book Pro, vec sam poskidao visak delova ...
Reply
yugaja Offline
Member
***
Posts: 165
Threads: 6
Joined: Jul 2015
Reputation: 120
#24
05-26-2017, 02:42 PM (This post was last modified: 05-26-2017, 02:43 PM by yugaja.)
Ja sam to (AVR-ove) u davna vremena  pre pojave svog ovog fenseraja  Smile przio iz pony prog-a: par tranzistora, otpornika i serijski port (ali "fizicki"...to mozda bude sada problem ili mozda i ne; uvek ima po koji PC krs u blizini...)
http://yugaja.co.nf
Reply
TDA Offline
Somewhere in Time
*******
Posts: 8.261
Threads: 77
Joined: Apr 2013
Reputation: 1.643
#25
05-26-2017, 02:44 PM
(05-26-2017, 02:35 PM)mikikg Wrote: Ma nema nista od mog laptop, Mac Book Pro, vec sam poskidao visak delova ...

Šteta. Sad
Face up...make your stand and realise you're living in the golden years!
Reply
Milan94 Offline
Senior Member
****
Posts: 556
Threads: 11
Joined: Apr 2014
Reputation: 150
#26
05-26-2017, 03:02 PM
Preneki dan sam przio Atmega8 preko pony prog iz windows7 sve radi kako treba skinuo sam novu verziju mislim da je nesto doradjena da radi iz novije OS a usput podrzava atmega328 samo je potrebno imati serijski port na racunaru.
Reply
mikikg Offline
Administrator
*******
Posts: 8.708
Threads: 138
Joined: Apr 2013
Reputation: 3.606
#27
05-26-2017, 03:21 PM (This post was last modified: 05-26-2017, 03:57 PM by mikikg.)
Samo da objasnim sta je caka sa tim seriskim portovima, ti programatori koriste tkz "bit banging" pristup, to je baratanje komunikacionim portom van standardnog RS-232 protokola, specificno se priprema signal koji se salje u kontroler da bi se isprogramirao.
Stare PC masine koje imaju na sebi seriski port (DB-9) podrzavaju "bit banging" u osnovi.

E sad, ima razlicitih USB<>Seriskih konvertera, razlikuje se chipset koji imaju na sebi, postoje sa FT232, PL2303 i jos nekoliko.
Koliko sam upucen samo FT232 podrzava bit-banging i mozda jos neki IC tog proizvodjaca, ovi ostali ne i to je cela caka kako osposobiti stare uredjaje/programe da rade sa USB konverterima. To je sto se tice prokola komunikacije, iza toga po potrebi se stavlja MAX232 koji samo vrsi naponsku konverziju logickih signala.

Takodje, zavisno od programatora, moze da se desi da je potrebno pored standardnih RX/TX linija potrebno jos i RTS, CTS, DTR, DSR signalne linije da bi programator radio, i tu nastaje problem ako imate USB<>Seriski konverter koji nema izvedene te linije iako ima DB-9 konektor.
Na primer ovaj konverter je dobar, ima izvedene sve seriske signale i podrzava bit banging, baziran je na FT232RL:

Reply
TDA Offline
Somewhere in Time
*******
Posts: 8.261
Threads: 77
Joined: Apr 2013
Reputation: 1.643
#28
05-26-2017, 03:49 PM
Milane, imaš neko uputstvo?
Face up...make your stand and realise you're living in the golden years!
Reply
Milan94 Offline
Senior Member
****
Posts: 556
Threads: 11
Joined: Apr 2014
Reputation: 150
#29
05-26-2017, 04:13 PM (This post was last modified: 05-26-2017, 04:17 PM by Milan94.)
TDA nema tu nikakvog specijalnog uputstva standardno skines najnoviju verziju Pony Prog instaliras radi na bilo kom novijem sistemu samo moras imati na racunaru RS232 port.

Da nebih pravio Interfejs mogu ja da ponesem sutra (ukoliko budem sa Goshom nasao prevoz) svoj SI Prog koji sam napravio.
Reply
tomam Offline
Member
***
Posts: 96
Threads: 13
Joined: Nov 2016
Reputation: 34
#30
05-26-2017, 05:09 PM
(05-26-2017, 04:13 PM)Milan94 Wrote: TDA nema tu nikakvog specijalnog uputstva standardno skines najnoviju verziju Pony Prog instaliras radi na bilo kom novijem sistemu samo moras imati na racunaru RS232 port.

Da nebih pravio Interfejs mogu ja da ponesem sutra (ukoliko budem sa Goshom nasao prevoz) svoj SI Prog koji sam napravio.

USBASP 250 din i radi na usb Smile
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)