Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
APEX SX9
#41
Dragane podeli svoj rad na diyaudio.com mislim da moze da bude zanimljivo uz to kako kaze TDA plocica je skoro gotova Smile
Reply
#42
Biće danas...
Face up...make your stand and realise you're living in the golden years!
Reply
#43
Da li može da prođe?
03-20-2018, 01:37 PM
03-20-2018, 01:38 PM

80x80mm
Face up...make your stand and realise you're living in the golden years!
Reply
#44
Spoji levi pad na otporniku 1k (ulaz).
Grupa na ulazu (1k, 22k i 100pF) bi se mogla zarotirati u smeru kazaljke na satu, malo povecati razmak izmedju padova za kondenzator, i onda ispod ovih komponenti spojiti otpornike 4k7/1W.
Reply
#45
Hvala Bob03.
Ispravljen je ulaz.
Nisam hteo da povratnu spregu provlačim ispod ulaznog kondenzatora.
Ovako je nekako najbezbolnije pošto vodovi se preklapaju najmanjom površinom.
Face up...make your stand and realise you're living in the golden years!
Reply
#46
Ukoliko nema više predloga za isprvku-doradu, ovako bi izgledala pločica.
03-20-2018, 03:52 PM
03-20-2018, 03:52 PM
03-20-2018, 03:52 PM


.lay6   APEX SX9 V.3.lay6 (Size: 140,68 KB / Downloads: 3)
Face up...make your stand and realise you're living in the golden years!
Reply
#47
Imenjače, zar 1K i 22K na ulazu ne bi trebali biti spojeni?
Reply
#48
Izvini, gledao sam gornju sliku, a ne zadnju...
Reply
#49
(03-20-2018, 07:50 PM)Millan Wrote: Imenjače, zar 1K i 22K na ulazu ne bi trebali biti spojeni?

Wink
https://www.youtube.com/watch?v=0p_1QSUsbsM
Face up...make your stand and realise you're living in the golden years!
Reply
#50
Na diyaudio,com su mi zamerili zato što se izlazna zavojnica nalazi preblizu ulaznog kondenzatora.
Evo još jedne ispravke.
03-21-2018, 12:10 PM
03-21-2018, 12:09 PM
03-21-2018, 12:10 PM


.lay6   APEX SX9 V.3.1.lay6 (Size: 140,82 KB / Downloads: 2)
Face up...make your stand and realise you're living in the golden years!
Reply
#51
I još malo premeštanja i zamene vrednosti da bi se uklopilo u Dragan100 šemu V.1.1


03-21-2018, 03:40 PM


.lay6   APEX SX9 V.3.2.lay6 (Size: 142,03 KB / Downloads: 2)
Face up...make your stand and realise you're living in the golden years!
Reply
#52
@Dragan100 i apexaudio
Momci,
već dugo se spremam da napravim APEX F8R.
03-23-2018, 12:28 PM

Da li možemo i njega ovako da uredimo, pa da crtam pločicu?
Face up...make your stand and realise you're living in the golden years!
Reply
#53
http://forum.yu3ma.net/showthread.php?tid=1838
Face up...make your stand and realise you're living in the golden years!
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)